"Made In The USA!"

Secure Online Shopping:

in

Loading...

Navigation

Contact Us

CARVER Custom

Customer Service

(904) 300-4211

Monday - Friday
10:00 AM to 5:00 PM

(Eastern Time Zone)

 

Order Online 24/7

Orders Received by 4:00 PM Mon-Fri

Shipped Same day

Handguns can be picked up or dropped off by appointment.

Monday - Friday

1:00 PM to 4:00 PM

(Eastern Time Zone)

by Appointment Only


Click Here to E-Mail

 

  Disclaimer

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.mbH. Neither CARVER Custom, Inc., nor this site are affiliated in any manner with, or otherwise endorsed by, Glock, Inc. or Glock Ges.mbH.  The use of “Glock” on this page is merely to advertise the sale of Glock pistols, parts, or components.  For genuine Glock, Inc. and Glock Ges.mbH products and parts visit www.glock.com.

CARVER Angle C-More Mount For XDM Handguns

Be the first to review this product

Availability: Out of stock

$165.00

Quick Overview

CARVER Custom Angle Mount for C-More sights can be used in USPSA, Steel Challenge, Bowling Pins or any fun shooting you and your friends enjoy. No modifications to the receiver or slide necessary when using this mounting system.

CARVER Angle C-More Mount For XDM Handguns

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

Details

The "NEW" CARVER Angle C-More Model has been designed to fit any of the full size XDM or XD handguns including Tactical, 4.5 and 5.5 models. Modifications to your XDM is not needed to install our CARVER Custom Angle Mount for XD/XDM. NOTE: Our tests have shown that lowering the ejection port with the use of the CARVER Angle mount is "NOT" necessary. Like all of our CARVER Mounting systems, installation is easy and should not require gunsmith assistance. No modifications to your receiver required. Installation requires the following: 1. Remove the slide from the frame. Please note: The front and rear sights will require removal 2. Remove the stock trigger pin from your XD. (A slight tap with a punch) 3. Remove the two screws on the bottom of the Underlug Insert, Part B of the Underlug, Part A, of the Mount. (picture below) 4. Remove the Left Sideplate of the mount using allen wrench supplied. 3 screws will need to be removed. (pictured below) Please note: Mount is shipped with these screws loosened. 5. Slide mount less the left sideplate over your frame starting at the accessory rail. 6. Reinstall the leftside plate over the takedown lever of the receiver. We recommend the use of blue loctite when these screws are installed. Don’t tighten. Leave screws loose. 7. Before tightening the screws on the left sideplate, install the Angle Plate by installing the 5 4-40 x 1/4" screws through the Angle Plate through the Center Plate and into the top of the left sideplate. Secure all screws by using blue loctite and tighten until snug. 8. Insert the Trigger pin through the mount (Right) side through the XD trigger pin hole and tighten screw into steel tap on (Left) side of mount. Note: An Allen wrench that will fit all screws is included with your mount. 9. Reinstall the Insert, Part B into the Underlug, Part A, with the 2 screws supplied. 10. Install your C-More by using the SHC screws supplied by your C-More Slideride after removing the 4 small screws holding the top plates in front of the module. Install onto Angle Plate. 11. Reinstall slide. 12. Check all screws for tightness. Your mount was shipped assembled with screws on the right sideplate tightened with loctite. The left sideplate was shipped with screws loosened to ease installation. The Angle Mount is shipped uninstalled. CAUTION: Don’t overtighten screws. We recommend using blue loctite on all screws except the 2 screws that hold the Insert in place on the Underlug. Adjustments to the Cmore is easy, following the instructions provided by Cmore. Access to the adjustment screws is available on the "left" side of the mount. All parts of this mount are CNC machined from high quality aircraft aluminum and comes with a Life Time Warranty against manufacturing or material flaws. The CARVER Angle mounts are available in either black or silver Type 2 Anodizing. If you want a different color, we will provide Cerakoting of the mount parts for an additional fee as noted. CARVER Custom Modified WSM2 holsters are available for your XD/XDM with this mount. Available from our online catalog. CARVER Thumbrest, optional, can be installed on this mount as well. If you have questions, please contact us at sales@carvercustom.com

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Click to add text...

Contact Us

Tel: 904-300-4211 (Sales/Support)

Monday - Friday 10:00 AM - 4:00 PM

(Eastern Time Zone)


Click Here to E-Mail

FFL/Shop Address

CARVER Custom, Inc.

5570 Florida Mining Blvd S

Building 100, Suite #106

Jacksonville, FL 32257

 

"At CARVER Custom, Inc., your satisfaction is our goal. Experience the difference"

Fast shipping, quality made products, personal service!

Mobile Site | Back to Top